3 نوفمبر 2026
حُدّث محرك الحساب إلى 1.26.4. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Boost Converter Design: duty, inductor, peak current, ripple and the right-half-plane zero.
- MLCC Effective Capacitance: what is left after tolerance, DC bias, temperature and ageing, and how many parts you need.
- A Protection and EMC group: Input EMI Filter and Damping, TVS and Surge Clamp, and Fuse Sizing with Inrush and I²t.
- Op-Amp Noise and DC Error, and Current-Sense Resistor and Amplifier, in a group now called Analog and Interfacing.
- Active Filter (Sallen-Key and MFB), Crosstalk and Spacing, and Line Termination and Reflections.
- An RF and Wireless group: L-Network Impedance Matching, and RF Link Budget and Range.
- NTC Thermistor to ADC, UART Baud Error and Timer Prescaler, and RC Snubber for Switch-Node Ringing.
- The side panel glides to the calculator you open, wherever you opened it from.
- From a calculator to any other page, a link at the top returns you to it with your values.
- Closed input groups open and close smoothly.
- Results change smoothly as you type: only the digits that changed move.
- Calculators open on everyday values, with ambient temperature at 25 °C.
- AC Resistance and Impedance no longer send a stripline plane spacing to other pages as a height.
- PDN Target Impedance judges from the regulator's loop bandwidth up, where its model holds.
- Charts move smoothly to their new shape as you type.
- Sources are named plainly, without section numbers, revisions or dates.
1 نوفمبر 2026
حُدّث محرك الحساب إلى 1.22.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Corrections across ADC, Voltage Divider, LED Series Resistor, LDO, MOSFET, Buck and six PCB calculators. Saved work whose answer moved is marked in Your work.
- The values beyond the basics, and the hints under a result, are part of Pro.
- Data charts draw as plots, with the x value named on hover and a logarithmic x axis where the range calls for it.
- Worst-case corners analyse the design as built and name the point that sets the worst case.
- Parameter sweep judges each step by the whole calculation and names where the verdict changes.
- Signed reports and review packs name the standard behind each check and carry the engineering disclaimer.
25 سبتمبر 2026
حُدّث محرك الحساب إلى 1.18.3. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Charts on Logic Power, Trace Width, Junction Temperature and Trace Inductance match the answers beside them.
- Units read plainly: Ω/sq, ppm/°C, °C/mV, dB/in, and ratios as 5.3:1.
- A Board profile button on every calculator it fills, and a Fab profile button where fab limits apply.
- Shorter labels, with the detail behind a ? beside each field.
- Parameter sweep: every step is drawn and named as in its table, on linear and log axes.
- Worst-case corners: sampled parts stay inside their tolerance.
24 سبتمبر 2026
حُدّث محرك الحساب إلى 1.18.1. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Three calculators: Transient Thermal Impedance, PDN Target Impedance, and AC Resistance, Skin Effect & Trace Loss.
- Every calculator judges its headline answer against a stated limit, or says why no verdict applies.
- Saved work that the current engine answers differently is marked Answer changed in Your work, with a link to what changed.
- Recent can be cleared, or switched off, in Your work.
- The About page counts calculators the same way as the rest of the site.
20 سبتمبر 2026
- Plans. Pro adds version history, parameter sweeps, worst-case corners, compare, full exports and unlimited signed reports.
- Parameter sweep: vary one input over a range and see the answer and verdict at every step, as a table and a curve, with CSV export.
- Compare two saved calculations side by side, with every difference marked.
- Version history: earlier edits of a saved calculation are kept.
- Pro features show a preview with a small Pro mark.
19 سبتمبر 2026
- Save on this device: Ctrl-S keeps the calculation on this device, offline too, with a title, project and notes. Sign in later and it joins your account.
- Continue with these values: links under the results carry your numbers into the next calculator.
- Board profile: enter copper weight, thickness, dielectric, ambient and junction limit once, in Your work, and every calculator that asks for them fills them in.
- Recent, at the top of the calculator list: your last computations, each a link that reproduces it.
- Your work shows how much of your plan is used, filters by tag, and offers undo when you delete.
8 سبتمبر 2026
حُدّث محرك الحساب إلى 1.8.1. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Show working under the answer on the ten most-used calculators: the equation with your numbers in it.
- The headline answer stays in view until the result scrolls into view, at every width.
- An empty number field shows the shorthand it accepts, such as 4k7, 100n and 3V3.
- 3V3 reads as 3.3 V, just as 4k7 reads as 4.7 kΩ.
- A comma reads as a decimal point: 2,5 is 2.5 and 4,7k is 4.7 kΩ. Grouped thousands still work, as in 1,000.5, and an ambiguous value is flagged rather than guessed.
- Areas and volumes print in a clear unit, such as 25500 µm² or 0.5 mm³.
- Every calculator marks one headline answer, with the values that drive the next decision beside it.
7 سبتمبر 2026
حُدّث محرك الحساب إلى 1.7.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Wire Gauge & Voltage Drop: the AWG a run needs for its current and drop, or what a chosen gauge does.
- Crystal Load Capacitance: the C1 = C2 pair for a crystal’s C_L, and the ppm error of the pair you have.
- Via Stub & Back-drill: the stub’s quarter-wave resonance against your data rate, and the longest stub that stays clear of it.
- Trace Inductance & di/dt: partial and loop inductance of a trace, and the voltage a current step produces.
- Via & Pad Geometry: annular ring after drill registration, aspect ratio and clearance against your fab’s capability, and the smallest pad that passes.
- Copy results on every calculator: inputs, answers, verdicts and the link, ready for design notes and reviews.
- Saved calculations can be pinned to the top of your work and carry a note.
- On a phone the headline answer stays in view while you edit inputs, and a calculator page prints as a clean document.
- Numbers in preset chips and option lists read correctly on Arabic pages.
19 أغسطس 2026
حُدّث محرك الحساب إلى 1.5.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- The impedance calculator also solves in reverse: give a target impedance and it finds the trace width, for every line type.
- Fabrication tolerances on w, h and ε_r give worst-case minimum and maximum impedance.
- The cross-section has its own panel, and delay is behind a toggle.
- Chart cursors read plain numbers, such as 0.20 mm, and move in finer steps.
18 أغسطس 2026
حُدّث محرك الحساب إلى 1.4.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- The impedance calculator covers six line types: surface and embedded microstrip, symmetric stripline, edge-coupled differential microstrip and stripline, and grounded coplanar waveguide.
- It now uses the Hammerstad-Jensen and Cohn/Wadell models. Saved impedance numbers shift by a few percent, and the page explains the change when you open them.
16 أغسطس 2026
حُدّث محرك الحساب إلى 1.3.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- The Voltage Divider takes its tolerance from the series you pick, for example ±1 % for E96.
- Report a problem, in the footer of every page.
- The consulting page has a form: pick what you need and describe the work.
- A Most popular shelf at the top of the calculator index.
- Saved calculations show their inputs, stored answer and verdict in the list.
12 أغسطس 2026
- Charts draw as soon as the page opens.
- The MOSFET loss split is a chart, so the three losses compare at a glance.
- An account menu in the header: your projects, saved work and sign-out.
- Less text on every calculator. The equations stay in view, and the longer discussion is behind More detail.
- A What’s new note after each release.
11 أغسطس 2026
- A three-state theme control: light, dark, or follow your system.
- A retuned light theme and one type scale.
- Every verification address printed on a report opens its verification page.
- Privacy and Terms rewritten in plain words.
10 أغسطس 2026
حُدّث محرك الحساب إلى 1.3.0. تُعاد النتائج المحفوظة وتُعلَّم أي تغييرات عند فتحها.
- Fields the calculator works out for you are read-only on every calculator.
- Equations are properly typeset, so fractions and roots stretch to fit.
- Redrawn charts, with sub-decade gridlines on logarithmic axes.